Orange Smart Socket Ios

1. Downloading the iOS Mobile App

The Dialog Smartlife mobile app can be installed in three simple steps.

  1. Open the “App Store” on your mobile device.

  2. Search “Dialog Smartlife” App

  3. Download and install the application. (The app is supported by iOS 9.0 or later)

2. Additional Information

2.1. Methods of Configuration

There are four ways of configuring the Smart Socket.

  1. Manual configuration without QR code.

  2. Manual configuration with QR code.

  3. WPS configuration without QR code.

  4. WPS configuration with QR code.

2.2. Keep your device in hand, unplugged. You will be required to scan to QR code on the bottom of your device.

2.3. Open the Dialog Smart Life App

You will be greeted with the welcome screen. Click on "Add featured device" to add the Smart Socket

2.4. You will then be asked if the device is to be added with a QR code.

2.4.1. Select Yes to Scan QR Code

You will then be asked if the device is to be added with a QR code. Select Yes. Scan the QR code when prompted by the app.

2.4.2. Select No to Continue manually

2.5. Select Device Brand

You will be asked to select the device brand at the next screen. Select Orange Electric.

2.6. Select Device Type

You will be asked to select the device type at the next screen. Select Switch.

2.7. On the next screen, you will be asked if the device you are trying to add is already connected to your home wireless (Wi-Fi) network.

2.8. Configure the Device

Put the device into configuration mode by:

2.8.1. Normal Mode

Step 1:

Plug in the Smart Socket into a 13A wall outlet. Make sure the wall outlet is switched off

Step 2:

Press and hold the button on the Smart Socket as soon as you turn on the power on the wall socket. Once the device powers on, the indicator on the Smart Socket will turn blue which will instantly turn red and then turn green. Release the button when the indicator turns green. The indicator should now blink in green to indicate the device is in configuration mode.

2.8.2. WPS Mode

NOTE:
WPS Mode should be enabled in your router for this

Press and hold the WPS button on your router.

Now put the device in WPS configuration mode by:
Step 1:

Plug in the Smart Socket into a 13A outlet.

Step 2:

Press and hold the button on the Smart Socket and then turn on the switch on the socket. Keep holding the button once the device powers on, until the indicators on the Smart Socket turn red. Release the button once the indicators turn red.

NOTE:
The indicator should turn off, turn on and then remain red to indicate the device is in WPS mode. Once configuration is done (or if it fails) the device continues its boot cycle.

2.9. Press “Start”

2.10. Connect to "Smart Socket" Wi-Fi Hotspot

  • Now open "Settings" on your phone and go to WiFi

  • Select the WiFi hotspot "Smart Socket" and connect.

  • Configure the password "12345678"

Now should be connected to the device

2.11. Enter Credentials

If the device has been properly set to configuration mode, the following screen will be displayed. Enter the following information:

  • SSID – Select the name of the network you want to connect to from the drop-down list.

  • Password – Enter the password for the WIFI network you are trying to connect to.

  • Name – Enter a (descriptive) name for your Smart Socket.
    • Eg: “Kitchen Socket”
  • Serial Number – Enter the serial number which can be found on the package of your Smart Socket.

2.12. If the configuration was successful, your new Smart Socket should be shown in the “Devices” page.

NOTE:
If this doensn't succeed make sure you have switched to an internet connection

Your Smart Socket can now be controlled via the Dialog Smart Life App. Refer Section 2.3 on how to control the device.

3. Indications & Operations

3.1. LED indications

The LED indicator on the Smart Socket can be used to monitor the status of the device.

The LED indications of the socket are as follows;

  • Upon successful connection to internet - 3 green blinks.
  • Upon connection attempt to server (inactive time) – Red (momentarily)
  • During operation

When the wall socket is turned on, the indicator would be continuously on. When the wall socket is turned off, the indicator would be continuously off.

During operation, the color of the indicator would depend on the connection status of the device.

  • No connection to internet – Red (continuous) when output is on.
  • Connected to the internet but no connection to server – Blue (continuous) when output is on.
  • Connected to the internet and server and device is operating normally – Green (continuous) when output is on.

Once turned on, the device starts to initialize. This is indicated by a blue blinking LED. After initialization, the device attempts to connect to the internet with the SSID and password last provided to the device. A successful connection is indicated by three green blinks of the indicators. When the device is ready to be used the indicators would flash once in one of the above colors to indicate its connection status and then turn off. The device powers on with the output in off mode.

Customer Support Hotline: +94 777 886886

  • Select Option 2 for Technical Support
Last updated on 4th Apr 2018